-
Monacor Monacor AIRMT-85 Bånddiskant: Klar Lyd 2500-30KHz, til Hi-fi Højttalere 150W
Vores lille Air-Motion transformer fra Monacor med krystal klar gengivelse helt nede fra 2500Hz og op til 30KHz. Som sin storebror AIRMT-130 har den flot dynamik, men er tiltænkt lidt mindre Hi-fi højttalere i størrelsen optil 150W vedvarende (RMS) som dækker de fleste højttaler byg. Her kan du med fordel trække delefrekvensen optil 5000Hz og dermed udvide dens evne til at optage effekt og dermed udvide dens dynamik. AIRMT-85 er mere retningsbestemt end en dome, som resultere i færre væg, gulv og loft reflektioner, og dermed bedre grundlag for et klart stereoperspektiv. Trods sin lille størrelse med 85mm i diameter, har den et stort membran areal grundet harmonika formen i membranen, som giver den fantastisk dynamik, som specielt lyttere med stor kærlighed til piano kan havde svært ved at finde en værdig diskant til at gengive, men som en diskant som denne kan nyde tangenterne blive anslået med meget lav forvrængning. Frontpladen er også for den kræsne højttaler bygger, udført i solid aluminium. TEKNISKE DATA: Impedance (Z) 4 Ω Operating voltage - Frequency range 2,000-30,000 Hz Resonant frequency (fs) - Rec. crossov. frequ. (fmax.) (12 dB/oct.) > 2,500 Hz Music power (PMAX) 40 W Power rating (PRMS) 20 W Sensitivity 92 dB/W/m Max. rated SPL - Max. voltage - Radiation angle - Suspension compl. (Cms) - Moving mass (Mms) - Mech. Q factor (Qms) - Electr. Q factor (Qes) - Total Q factor (Qts) - Equivalent volume (Vas) - DC resistance (Re) 3.8 Ω Force factor (BxL) - Voice coil induct. (Le) - Voice coil diameter - Voice coil former - Linear excursion (XMAX) - Eff. cone area (Sd) - Magnet weight - Magnet diameter neodymium rods Mounting cutout Ø 66 mm Mounting depth 35 mm Mounting hole diameter Ø 75 mm Hole spacing X - Hole spacing Y - Dimensions Ø 85 mm Outside diameter Ø 85 mm Width 85 mm Height 85 mm Depth - Admiss. ambient temp. 0-40 °C Weight 0.288 kg
1.399,00 kr
-
Monacor Monacor Airmt-130 Højttalerenhed - Klart Lydbillede, Lav Forvrængning
Topmodellen af Air-Motion Transformers fra Monacor, som er en type diskant der mest minder om bånddiskanter og er derfor typisk kategoriseret sammen med disse. AIRMT-130 giver en fantastisk flot transient gengivelse, igennem et super flot og klart lydbillede med lav forvrængning. Grunden til at den har lav forvrængning er at membran arealet er meget stort i forhold til størrelsen af selve diskanten, AIRMT-130 har ca 10x så stort et areal som en tilsvarende dome. Det er opnået ved lave en folie som er formet ligesom harmonika, hvorpå der ligger ledende baner som tilsluttes forstærker effekten overfor et stærkt neodymium magnet felt. Dette resultere i at AIRMT-130 kan tåle en vedvarende forstærker effekt (RMS) på hele 60W med en følsomhed på 98dB, som giver den Hi-fi mæssigt rigtigt stort head-room, som betyder at piano anslag bliver utrolig virkeligheds tro, som er noget af det svære for en diskant at gøre. Denne type diskant skal helst bruges i et 3 vejs system da den skal havde en delefilter deling ved 3000Hz eller højere, vi har bas/mellemtoner som kan møde dette krav som 2 vejs, hovedsageligt Excel serien fra Seas. AIRMT-130 er mere retnings bestemt end en dome, som resultere i færre refleksioner fra vægge og loft, og dermed en forbedre klarhed i stereoperspektivet. Igennem sin præcision og store evner dynamisk er det helt klart vores anbefaling til den krævende klassisk musik lytter. Flot præsentable front plade i robust aluminium, som understreger kvalitet og et produkt for den kræsne lytter. TEKNISKE DATA: Impedance (Z) 8 Ω Operating voltage - Frequency range 2,500-30,000 Hz Resonant frequency (fs) - Rec. crossov. frequ. (fmax.) (12 dB/oct.) > 3,000 Hz Music power (PMAX) 120 W Power rating (PRMS) 60 W Sensitivity 98 dB/W/m Max. rated SPL - Max. voltage - Radiation angle - Suspension compl. (Cms) - Moving mass (Mms) - Mech. Q factor (Qms) - Electr. Q factor (Qes) - Total Q factor (Qts) - Equivalent volume (Vas) - DC resistance (Re) 5.2 Ω Force factor (BxL) - Voice coil induct. (Le) - Voice coil diameter - Voice coil former - Linear excursion (XMAX) - Eff. cone area (Sd) - Magnet weight - Magnet diameter neodymium rods Mounting cutout 71 x 111 mm Mounting depth 40 mm Mounting hole diameter - Hole spacing X 76 mm Hole spacing Y 116 mm Dimensions 130 x 90 mm Outside diameter - Width 130 mm Height 90 mm Depth 40 mm Admiss. ambient temp. 0-40 °C Weight 0.58 kg
2.249,00 kr
-
Monacor RBT-56 Mini Bånddiskant: Krystalklar Diskant op til 40KHz - 10W RMS
Med RBT-56 kan du med et meget lille budget få magnetstat lyd i de høje toner, denne lille bånddiskant giver flot detaljeret diskant op til 40KHz men skal deles ved 5500Hz grundet dens lave belastbarhed. Derfor egner den sig perfekt som super tweeter i et 4 vejs system, men kan bestemt også være diskant i et 3 vejs system med en god mellemtone, her skal du blot sikre dig den pågældende mellemtone ikke har opbrud før 5500Hz, for at sikre flot og rolig gengivelse. 10W ser ud som meget lidt, men man skal tænke på at når delefrekvensen ligger så højt i frekvens vil kun ca 10% af forstærker effekten blive afsat i diskanten, og dermed vil denne diskant være god i en højttaler op til omkring 100W vedvarende (RMS). Alt i alt giver RBT-56 en fantastisk mulighed for at få krystal klar high-end diskant gengivelse på et lille budget og det er noget vi kan li hos Bekent. TEKNISKE DATA: Impedance (Z) 4 Ω Operating voltage - Frequency range 5,000-40,000 Hz Resonant frequency (fs) - Rec. crossov. frequ. (fmax.) (12 dB/oct.) 5,000 Hz Power rating (PRMS) 10 W Peak music power output (PMAX) 20 W Sensitivity 90 dB/W/m Max. rated SPL - Max. voltage - Radiation angle - Suspension compl. (Cms) - Moving mass (Mms) - Mech. Q factor (Qms) - Electr. Q factor (Qes) - Total Q factor (Qts) - Equivalent volume (Vas) - DC resistance (Re) 3.5 Ω Force factor (BxL) - Voice coil induct. (Le) - Voice coil diameter - Voice coil former - Linear excursion (XMAX) - Eff. cone area (Sd) - Magnet weight - Magnet diameter magnetostatic speaker Mounting cutout Ø 40 mm Mounting depth 10 mm Mounting hole diameter Ø 48 mm Hole spacing X-axis - Hole spacing Y-axis - Dimensions Ø 56.5 mm x 10 mm Outside diameter 56.5 mm Width 56.5 mm Height 56.5 mm Depth - Protective class Admiss. ambient temp. 0-40 °C Weight 0.046 kg
299,00 kr
-
Earthquake Earthquake SWS-12X Basenhed - Dyb bas uden dyb konstruktion
The Earthquake “SWS” - Shallow Woofer System- Provides more sound from less space with less power than any other woofer technology. The core technology of the SWS was pioneered by Earthquake Sound's President Joseph Sahyoun and is now protected by multiple global patents.The “SWS” design moves the flexible suspension components(cone & spider) to the side allowingthe motor to be elevated. This reduces the mounting depth of the speaker while enhancing excursion capability. More excursion (woofer movement) equals more sound.Upgrading to SWS is both attractive and simple :1. Direct factory drop-in replacement.2. Greatly enhanced sound quality. Enjoy a rich full bodied sound with articulation and dynamics rivaling home hifi audiophile systems.3. Plays louder and cleaner than standard woofer - using less power.4. Works perfectly with factory amplifier, while still capable of further SPL with upgraded amplifiers.The modern luxury car buyer expects all aspects of their vehicle to be thrilling and engaging. Thiselevates the expectations for the audio system as people now carry their music with them where ever they go - making comparisons easy. They want it to sound as good as it possibly can while being on the road. Preferably it should be so good in the car that the driver looks forward to both the ride and the music. With Earthquake SWS woofers the authentic and authoritative sound is always at the driver fingertips.Designing sound quality :“SWS” technology employs a patented ribbed cone that eliminates cone break-up distortion while maintaining a light moving mass. This keeps the woofer nimble, fast and accurate. This fast acoustic response makes the sound engaging and entices the listener to turn up the sound as it just sounds “finger snapping good”.Designing durability :“SWS” employs a revolutionary innovation that welds an aluminum voice coil to an aluminum dust cap thus turning it into a heat sink. This heat exchanger uses convection/ conduction to transfer the heat out of the box. This increases the woofer performances and ensures that heat derived compression never occurs.In short :The “SWS” will play louder and more accurate while using less power and taking up less space than any other woofer on the planet. Our most popular size is the SWS-8” as it is a direct drop-in BMW factory replacement for the woofers located under the front seats. Simply remove the seats and replace the factory woofers with the SWS-8 woofers to improve the sound quality.Earthquake Sound also produces the SWS-8Xi that has a 2Ω voice coil - the same impedance as the BMW factory speakers.Sold and priced per piece. Features: Low profile mount for placement anywhere 4-Ohm impedance Inverted style cone design for maximum excursion in shallow mount applications High temperature voice with heat-sink attachment NOMEX/ROMEX spider assembly Protected by 3 U.S. patents Aluminum Bobbin Specifications: Model: SWS-12X EAN: 0-168975-910202 Size: 12" high performance sub Fs: 24Hz Max Power: 600W RMS Power: 300W Impedance: 4Ω Sensitivity: 89.4dB Qes: 0.515 Qms: 3.56 Qts: 0.45 Dimensions: SWS-12X Manual SWS-12X Product Release
2.169,00 kr
-
Earthquake Earthquake TNT-10DVC Subwoofer - 10", 1000W, Højtydende Bas
Extreme value - hard hitting bass The TNT woofers are the perfect upgrade to your sound system. With beautiful space age polymer cones they are a joy to look at and their articulated sound will enrich your life with quality sound. Professional voice coil The TNT voice coil is built with several professional features. The coil itself is made with copper wire.The voice coil former (the cylinder to which the coil is wound) is made of aluminum, not cellulose (cardboard), Kapton ® or fiberglass. The use of aluminum prevents hotspots on the voice coil - due to the superb heat conductivity inherent to aluminum. In essence the entire voice coil becomes one big heat sink. Stong magnet The TNT woofers use double thick high density magnets. The thick magnet allows the woofer to play louder while still sounding taunt and chrisp. The magnet is covered with an aesthetic rubber sleeve. Triple Vent The TNT woofers are equipped with Earthquakes Triple Vent scheme that enhances the voice coil cooling by maximizing airflow. Triple Vent combines the benefits of pole piece venting, voice coil radial venting and Spider venting. Triple Vent lets you play louder and longer. Prisen er pr.stk. Features: Polypropylene Cone Bodies Spring Loaded Terminals Triple Voice Coil Ventilations Thick High Density Magnet High Roll Surround Specifications: Model: TNT-10DVC EAN: 0-168975-910547 1000 Watts Max (300 WRMS) Xmax: 2" 10" subwoofer 2 x 4Ω dual voice coil 2" 4-wound Aluminum bobbin voice coil 120 oz. double stacked magnet Dimensioner:
669,00 kr
-
Earthquake Earthquake TNT-12S: 12" Basenhed, 400W - Perfekt til Elektronisk Musik
Denne bas levere virkelig meget bas for pengene. Se vedhæftede foto med kabinetforslag. Det er selvfølgelig muligt at vælge en billigere forstærker end den der er i Room Drop 12, med den anbefalede SAM-500D forstærker passer perfekt til denne voldsomme TNT Earthquake bas. Det er helt klart elektronisk musik at denne subwoofer komplimentere bedst, det betyder bestemt også at den kan klare sig fortræffeligt i en hjemmebiograf. Men der er noget slag i takten på TNT bassen at der kan mangle på en biograf dyb tunet subwoofer, der tilgengæld vil havde dens forza overfor en film. Extreme value - hard hitting bass The TNT woofers are the perfect upgrade to your sound system. With beautiful space age polymer cones they are a joy to look at and their articulated sound will enrich your life with quality sound. Professional voice coil The TNT voice coil is built with several professional features. The coil itself is made with copper wire.The voice coil former (the cylinder to which the coil is wound) is made of aluminum, not cellulose (cardboard), Kapton ® or fiberglass. The use of aluminum prevents hotspots on the voice coil - due to the superb heat conductivity inherent to aluminum. In essence the entire voice coil becomes one big heat sink. Stong magnet The TNT woofers use double thick high density magnets. The thick magnet allows the woofer to play louder while still sounding taunt and chrisp. The magnet is covered with an aesthetic rubber sleeve. Triple Vent The TNT woofers are equipped with Earthquakes Triple Vent scheme that enhances the voice coil cooling by maximizing airflow. Triple Vent combines the benefits of pole piece venting, voice coil radial venting and Spider venting. Triple Vent lets you play louder and longer. Prisen er pr.stk.Features: Polypropylene Cone Bodies Spring Loaded Terminals Triple Voice Coil Ventilations Thick High Density Magnet High Roll Surround Specifications: Model: TNT-12S EAN: 0-168975-910554 1250 Watts Max (400 WRMS) Xmax: 2" 12" subwoofer 2" 4-wound Aluminum bobbin voice coil Single 4Ω voice coil Dimensioner:
749,00 kr
-
Earthquake Earthquake Pro-X12 Basenhed: Høj Ydeevne
Pro-X12: Høj ydeevne og værdi i én professionel basenhed Introduktionen til Pro-X Professional Subwoofers fra Earthquake Sound er en linje af højfølsomme og bredbånds professionelle bas-højttalere, der er bygget med den akkumulerede viden og ekspertise, der er opnået gennem 30 års produktion af industridefinerende bas-højttalere. Pro-X beviser, at det er muligt at kombinere høj ydeevne med superior værdi. I årevis har det været vores analyse, at markedet for pro bas-højttalere er opdelt mellem ydeevne og værdi. De førende mærker bygger $1500+ "stjerneskib" bas-højttalere, mens et næsten uendeligt antal ingen-navn-mærker oversvømmer markedet med billige, men essentielt værdiløse bas-højttalere. Vi tilbyder Pro-X som den meningsfulde løsning ved at give nær enterprise-niveau ydeevne til mindre end en tredjedel af omkostningerne. Introducing Pro-X Professional Subwoofers Pro-X is the line of high sensitivity wide-band professional woofers from Earthquake Sound. Built with the accumulative knowledge and expertise gained from manufacturing industry defining woofers for 30 years. Pro-X is proof positive that the combination of high performance and superior value is possible! For years its been our analysis that the pro woofer market has a huge split between performance and value. The leading brands build $1500+ starship woofers and an almost unending slough of no-name brands flood the market with cheap, but essentially worthless woofers. We offer Pro-X as the meaningful solution. Providing near enterprise level performance at less than a third of the cost. Typically when designing a statement product its an exercise in the use of exotic materials and blatant disregard for the cost as a way of infusing exclusivity into the product. With Pro-X the goal was just the opposite - chip away all non-essentials and unearth the raw essence of performance. During this process we developed several technologies and design attributes that would come to be essential for the final product. PWT Voice Coil The PWT (Parallel Winding Technology) voice coil is a quite simple but effective method for approaching esoteric edge-wound voice coils in efficiency and thermal durability. Ordinary voice coils are wound with a single wire applied to the former x number of turns. The PWT coil uses two thinner wires applied to the former in parallel (wound side by side) x number of turns. This significantly increases surface area for improved thermal rigidity while keeping the same impedance as if regular single strand wire had been used. At a fraction of the cost of edge-wound, the PWT voice coil is instrumental in keeping the price down and performance up. L-RAE Motor Cooling Geometry Pro-X features the L-RAE (Large Radial Air Emitter) cooling scheme, and is the first Earthquake product to do so. We had intended to use our patented TCT (Turbine Cooled Technology); however, TCT was developed for heavy, long stroke woofers and was not ideal for the quick, taunt and agile characteristics of the Pro-X woofer. L-RAE is comprised of large unrestricted passages offering zero resistance to the moving air. A large drilled out pole piece with above spider side venting channels is combined with oversized radial cooling passages, matching the diameter of the voice coil. This efficiently transports air around the voice coil and reduces the air resistance on the moving voice coil itself. The result is a remarkably capable cooling system that compared to a traditional pole venting scheme, reduces temperatures by 40 percent. All without adding acoustic artifacts or cost to the equation. High Gauss Ceramic Magnet The brute magnetic force in the Pro-X is supplied by an oversized ceramic magnet. This high Gauss magnet concentrates immense magnetic flux on the voice coil resulting in stellar efficiency and tight chest slamming low frequency response. Designed with a bumped back extended pole piece for added excursion potential. This also protects the voice coil from bottoming out in case of transient overload. Legendary Chassis Any seasoned pro audio tradesman will recognize the chassis and smile. Yes it is 30+ years old, but from a performance viewpoint - a better one has yet to be made. Versatility Although designed as a pro audio woofer, it can be used in both home and automotive solutions with great success. It can be used in any application where large amounts of low distortion, wide-band acoustical power is needed. It is ideal for use in small sealed and ported enclosures as well as bass and mid-bass horns. Featuring a very shallow mounting depth the Pro-X can be used in specialty form factor systems. Value Built from the ground up with the fundamental elements that makes a product distinctly Earthquake - Power, Performance and Quality. Pro-X offers amazing performance at an unparalleled price. It is our sincere belief that the combination of price, performance and quality makes the Pro-X the best in this category on the market today. Proven Track Record For 3 decades Earthquake has been designing and manufacturing top quality audio equipment. The Pro-X is no exception to this ledger of excellence. We are certain they will provide many years of faithful service. Sold and priced per piece.
1.750,00 kr
-
Earthquake Earthquake SUBZERO-10 Woofer: Revolutionært Design til Musikenthusiaster
Klik på linket her for at få et system forslag til Subzero 10. Man kunne forledes til at tro at den har sin styrke til hjemmebiograffen, men egentlig er det mere det musikalske. Subzero -When only the best will do This latest iteration of Subzero is a tour de force of how advanced design and technology can come together to create superior sound quality. All aspects of the design have been perfected to the smallest detail, resulting in truly revolutionary woofer performance. Subzero is capable of an incredible 3" excursion (12" Subzero). With excursion of this magnitude, Subzero produces levels of bass unattainable by conventional woofers. The extreme excursion ability coupled with the unique suspension makes Subzero extremely transient proficient. Even a light touch on the cone, easily moves it several centimeters. This ease of movement combined with the ultra-powerful magnet system results in a spectacularly fast and precise response. Subzero is free of the mechanical and electrical constraints inherent to common woofers. Lava-fused Octo Helix voice coil Subzero is equipped with a unique voice coil of oversized proportions. All aspects of the voice coil design are optimized for maximum performance, durability and sound quality.In the creation of the Subzero voice coil, Earthquake scientists have boldly challenged the very genesis of the voice coil itself. Traditionally, a lot of effort goes into choosing the right voice coil former (the cylinder to which the coil is wound). The former must be light, have similar heat expansion properties to the voice coil and it must promote cooling. Constantly advancing the state of the art, Earthquake engineers theorized that the best solution must be to have no former at all. While this theory flies in the face of all conventional wisdom, our engineers pressed on. During this proof-of-concept phase, it was realized that the technology needed to do away with the former simply did not exist. Instead of abandoning the quest for formerless technology, the research was extended to include facilitating technologies. In place of the structural support provided by the former, a super strong ultra high temperature adhesive was needed. A new insulator for the coil wire was also needed as traditional lacquer insulator does not have sufficient bonding properties for it to fuse together at the required tensile strength. This challenge was constructive in its own right as the biggest threat to woofer survival is heat, if the essence of this new technology would bring forth a temperature resilient voice coil it would serve to improve all other aspects of woofer operation. The creation of the needed high temperature adhesive proved difficult and the next break would come as an unlikely discovery by our Chief engineer while on vacation in Hawaii. Taking a scenic tour of Hawaii, he was walking through an area with volcanic ash and realized that the ideal base substance for a high temperature adhesive would be a material with no combustible elements left. Volcanic ash fits this description perfectly as it has been exposed to extreme heat - it has been combusted to the point where further heat exposure will not change its molecular structure. The volcanic ash was taken to our German adhesive manufacturing partner and six months later we had our next generation temperature invariant super adhesive. Now we just needed an equally temperature resistant insulator. The only known insulator capable of withstanding this immense heat was anodizing. Anodizing however is problematic because it breaks off the host material if it is bent beyond a certain point. After much experimentation it was discovered that it is possible to prevent the anodizing from breaking off if the coil wire is heated to red hot temperature at the time of winding. Finally, the first former-less voice coil could be made. The audible qualities springing from this new lighter and stronger coil type is nothing less than remarkable. Signature technologies such as the Octo-Helix winding scheme has evolved for use in the new Subzero. The Octo-Helix design requires a very advanced production process. The Helix design is unique because it allows identical electromagnetic coupling and thermal signatures of two voice coils. In a conventional subwoofer with dual voice coils, they are wound one on top of the other, resulting in asymmetrical electromagnetic coupling and heat dissipation capability. The Helix structure is free of these limitations, since the two coils are wound synchronously in-phase. The Helix wound voice coil is characterized by several obvious advantages - perfect electromagnetic coupling, identical thermal signature, lower distortion, higher performance and durability. The voice coil is comprised of eight (octo) layers of edge wound oxygen-free copper wire. This special copper wire is of the flat-wire type. Flat-wire has a much greater surface area than conventional round wire and can thus dissipate considerably more heat it. Another advantage is the coil can be wound closer - increasing motor power. The coil assembly meets mil-std specifications for temperature resilience - specifications set by the U.S. Department of Defense for use in military equipment. This guarantees peak performance even during hard and continuous operation. TCT - Turbine Cooled Transducer Subzero is equipped with the patented TCT (Turbine Cooled Transducer) technology. TCT creates cooling airflow similar to a tornado around the voice coil. The tornado is created by air forced through cooling channels milled in a vortex structure. Traditional voice coil cooling is done by drilling out the pole piece and the woofer stroke then pushes air back and forth. This cooling scheme only has a linear increase as a function of woofer stroke. TCT is different. TCT creates an exponential increase in cooling capacity as a function of woofer stroke. This is achieved by harnessing the centrifugal forces in the mini tornado to increase surface area contact between the air and voice coil. TCT is so effective that the voice coil temperature is reduced 50% compared to the same woofer without TCT. This prevents heat derived compression and keeps the woofer at maximum efficiency.. The compression is a result of the increased electrical resistance of the voice coil - the higher the temperature, the higher the resistance. Since TCT's cooling capacity increases exponentially with excursion, heat is not allowed to build up. The harder you drive Subzero the more it cools itself. Poly-Ether draw SWE (Super Wide Edge) suspension For Subzero our unique SWE (Super Wide Edge) suspension design has been enhanced by the use of Poly-Ether draw material. Sporting an extreme curve height of 62 mm the stage has been set for incredible excursion. The manufacturing of this advanced suspension is a complex process spanning several stages. Poly-Ether draw is used primarily in military applications because of its high strength and flexibility. The sophisticated and costly processing requirements has so far limited its use outside the military. Thanks to the obsessive high-tech emphasis by Earthquake, the entire Poly-Ether draw manufacturing process can be done in-house. As part of the manufacturing process, the Poly-Ether material is thermally pressed and laminated giving it extreme strength and mobility. The suspension geometry is of the single-layer type and allows ultra long excursion without mechanical breakup. This results in woofer stroke potential in excess of 100 mm without deformation or increased mechanical resistance.This ensures perfect reproduction of even the most bass heavy soundtracks Parabolic deep dish woofer cone The Subzero cone is made of a proprietary non-pressed fiber reinforced cellulose pulp substance with extreme stiffness. The cone is then superimposed with a parabolic deep dish made of a strong space age polymer that obtains additional rigidity by its geometric shape. The cone does not flex or deform regardless of input power and frequency. Dual Super-Spider with composite center and symmetric stitched tinsel leads The Subzero spider is of the super spider type, which means the spider has the same diameter as the cone -this ensures the spider is not limiting excursion. The Subzero is equipped with a double super spider unit comprised of a Nomax /Romax hybrid material that has been epoxy coated for increased strength. The individual super spider units are arranged as identical opposites - canceling nonlinearities inherent to typical single or dual spider designs.The result is a clean sound - free from mechanical artifacts. For optimal performance the edge suspension and spider must have the same excursion potential, this is not possible with a traditional spider of limited diameter. Traditionally, the spider is glued to the voice coil, this results in heat transfer from the voice coil to the spider. This heat transfer effects the spiders compliance and can over time degrade the spider. The Subzero super spider is not glued the voice coil, but attached to a composite center ring that in turn is bonded to the voice coil. The special composite material is neither heat sensitive nor a thermal conductor. Thus the endurance and longevity of the Subzero is not affected regardless of drive level. The tinsel leads to the voice coil are sewn into the spider to ensure against collision with the cone during extreme excursion. This also extends the life of the tinsel leads, as they now bend more gently over a longer distance. The symmetrical design of the tinsel leads prevents an asymmetrical pull on the cone. The result is longer woofer life, and greater endurance. Double stacked Cobalt-Ceramic high gauss magnet system Subzero is built around a gigantic magnet system. It consists of two huge Cobalt-Ceramic magnets which have been hyper magnetised in-house by Earthquakes military grade Magnetiser. The two magnets have a total thickness of 6 cm, the top plate alone is 1 cm and the pole piece is 5 cm. With a total height of 12 cm - the voice coil is given unhindered travel space far beyond its mechanical limits. This ensures that not even the strongest transient may cause the device to run out of electromagnetic coupling. At the same time the high gap height contributes to voice coil cooling, as the immense mass of metal effectively absorbs heat. Diamond cut chassis with XLT geometry The Subzero is based on Earthquakes signature XLT chassis geometry. It is the optimal design for extreme excursion. The XLT chassis allows for extra length between the spider (center suspension) and the magnetic gap. It is designed to accommodate oversized spiders and voice coils. The Subzero chassis feature another advanced design detail unique to the Subzero. All other woofers have the chassis mounted on top of the magnet. The Subzero encases the magnet within the chassis and the chassis is mounted to the magnet from behind. This special design prevents the chassis from degrading the magnetic flux asserted on the voice coil. The oversized and rigid chassis is made of cast aluminum which is then diamond cut. This results in an ultra-rigid and robust chassis featuring stunning good looks. The chassis is further characterized by all components of the assembly being bolted together with stainless steel machine screws. This design is extremely rugged compared to ordinary assemblies where the chassis and magnet system is often glued and / or tabbed together. The technically superior design ensures exceptional durability, sound quality and pride of ownership. Pris er pr. stk. Specifications: Model: Subzero-10 EAN: 1-1411168-975915 Size: 10" Fs: 26.8Hz Max Power: 1500W RMS Power: 750W Mechanical Xmax = 3" peak to peak Electrical Xmax = 1.5" peak to peak Impedance: dual 4Ω Sensitivity:85.9dB Dual Nomax / Romax spider 8 gauge speaker terminals Patented PSP terminal BL 70% @ Xmech Dimensions: Diameter: 264mm Cut-Out Diameter: 292mm Mounting Diameter: 195mm TS Parameters: TS data obtained using the VI-BOX high power system. Specs measured @ 100watt rms. Standard TS is done @ 1-3 watt, insufficient for obtaining true data in a high excursion modern woofer. Fmd= 3.0000 KA Qmd= 1.0000 Flp= 8.0000 KA Qlp= 2.0000 Znom= 8.0000 Ohm Revc= 7.7000 Ohm Sd= 33.0000E-3 M² Mmd= 152.3169E-3 Kg Rtvc= 250.0000E-3 °C/W Xcoil= 3.0000 In Xmax= 31.7500E-3 M Krm= 52.9380E-3 Ohm Erm= 667.0000E-3 Kxm= 78.4200E-3 H Exm= 685.0000E-3 Rms= 19.3984 N-S/M Mms= 155.7620E-3 Kg Cms= 197.1628E-6 M/N Vas= 1.0830 Ft³ Fo= 28.7195 Hz Qms= 1.4489 Qes= 0.6994 Qts= 0.4717 BL= 17.5913 T-M Levc= 4.9888E-3 H SPLo= 82.0000 dB No= 99.5821E-3 %
3.399,00 kr
-
Earthquake Earthquake SUBZERO-12 Basshøjttaler med Ekstrem Excursion og TCT-Køling
Subzero -When only the best will do This latest iteration of Subzero is a tour de force of how advanced design and technology can come together to create superior sound quality. All aspects of the design have been perfected to the smallest detail, resulting in truly revolutionary woofer performance. Subzero is capable of an incredible 3" excursion (12" Subzero). With excursion of this magnitude, Subzero produces levels of bass unattainable by conventional woofers. The extreme excursion ability coupled with the unique suspension makes Subzero extremely transient proficient. Even a light touch on the cone, easily moves it several centimeters. This ease of movement combined with the ultra-powerful magnet system results in a spectacularly fast and precise response. Subzero is free of the mechanical and electrical constraints inherent to common woofers. Lava-fused Octo Helix voice coil Subzero is equipped with a unique voice coil of oversized proportions. All aspects of the voice coil design are optimized for maximum performance, durability and sound quality.In the creation of the Subzero voice coil, Earthquake scientists have boldly challenged the very genesis of the voice coil itself. Traditionally, a lot of effort goes into choosing the right voice coil former (the cylinder to which the coil is wound). The former must be light, have similar heat expansion properties to the voice coil and it must promote cooling. Constantly advancing the state of the art, Earthquake engineers theorized that the best solution must be to have no former at all. While this theory flies in the face of all conventional wisdom, our engineers pressed on. During this proof-of-concept phase, it was realized that the technology needed to do away with the former simply did not exist. Instead of abandoning the quest for formerless technology, the research was extended to include facilitating technologies. In place of the structural support provided by the former, a super strong ultra high temperature adhesive was needed. A new insulator for the coil wire was also needed as traditional lacquer insulator does not have sufficient bonding properties for it to fuse together at the required tensile strength. This challenge was constructive in its own right as the biggest threat to woofer survival is heat, if the essence of this new technology would bring forth a temperature resilient voice coil it would serve to improve all other aspects of woofer operation. The creation of the needed high temperature adhesive proved difficult and the next break would come as an unlikely discovery by our Chief engineer while on vacation in Hawaii. Taking a scenic tour of Hawaii, he was walking through an area with volcanic ash and realized that the ideal base substance for a high temperature adhesive would be a material with no combustible elements left. Volcanic ash fits this description perfectly as it has been exposed to extreme heat - it has been combusted to the point where further heat exposure will not change its molecular structure. The volcanic ash was taken to our German adhesive manufacturing partner and six months later we had our next generation temperature invariant super adhesive. Now we just needed an equally temperature resistant insulator. The only known insulator capable of withstanding this immense heat was anodizing. Anodizing however is problematic because it breaks off the host material if it is bent beyond a certain point. After much experimentation it was discovered that it is possible to prevent the anodizing from breaking off if the coil wire is heated to red hot temperature at the time of winding. Finally, the first former-less voice coil could be made. The audible qualities springing from this new lighter and stronger coil type is nothing less than remarkable. Signature technologies such as the Octo-Helix winding scheme has evolved for use in the new Subzero. The Octo-Helix design requires a very advanced production process. The Helix design is unique because it allows identical electromagnetic coupling and thermal signatures of two voice coils. In a conventional subwoofer with dual voice coils, they are wound one on top of the other, resulting in asymmetrical electromagnetic coupling and heat dissipation capability. The Helix structure is free of these limitations, since the two coils are wound synchronously in-phase. The Helix wound voice coil is characterized by several obvious advantages - perfect electromagnetic coupling, identical thermal signature, lower distortion, higher performance and durability. The voice coil is comprised of eight (octo) layers of edge wound oxygen-free copper wire. This special copper wire is of the flat-wire type. Flat-wire has a much greater surface area than conventional round wire and can thus dissipate considerably more heat it. Another advantage is the coil can be wound closer - increasing motor power. The coil assembly meets mil-std specifications for temperature resilience - specifications set by the U.S. Department of Defense for use in military equipment. This guarantees peak performance even during hard and continuous operation. TCT - Turbine Cooled Transducer Subzero is equipped with the patented TCT (Turbine Cooled Transducer) technology. TCT creates cooling airflow similar to a tornado around the voice coil. The tornado is created by air forced through cooling channels milled in a vortex structure. Traditional voice coil cooling is done by drilling out the pole piece and the woofer stroke then pushes air back and forth. This cooling scheme only has a linear increase as a function of woofer stroke. TCT is different. TCT creates an exponential increase in cooling capacity as a function of woofer stroke. This is achieved by harnessing the centrifugal forces in the mini tornado to increase surface area contact between the air and voice coil. TCT is so effective that the voice coil temperature is reduced 50% compared to the same woofer without TCT. This prevents heat derived compression and keeps the woofer at maximum efficiency.. The compression is a result of the increased electrical resistance of the voice coil - the higher the temperature, the higher the resistance. Since TCT's cooling capacity increases exponentially with excursion, heat is not allowed to build up. The harder you drive Subzero the more it cools itself. Poly-Ether draw SWE (Super Wide Edge) suspension For Subzero our unique SWE (Super Wide Edge) suspension design has been enhanced by the use of Poly-Ether draw material. Sporting an extreme curve height of 62 mm the stage has been set for incredible excursion. The manufacturing of this advanced suspension is a complex process spanning several stages. Poly-Ether draw is used primarily in military applications because of its high strength and flexibility. The sophisticated and costly processing requirements has so far limited its use outside the military. Thanks to the obsessive high-tech emphasis by Earthquake, the entire Poly-Ether draw manufacturing process can be done in-house. As part of the manufacturing process, the Poly-Ether material is thermally pressed and laminated giving it extreme strength and mobility. The suspension geometry is of the single-layer type and allows ultra long excursion without mechanical breakup. This results in woofer stroke potential in excess of 100 mm without deformation or increased mechanical resistance.This ensures perfect reproduction of even the most bass heavy soundtracks Parabolic deep dish woofer cone The Subzero cone is made of a proprietary non-pressed fiber reinforced cellulose pulp substance with extreme stiffness. The cone is then superimposed with a parabolic deep dish made of a strong space age polymer that obtains additional rigidity by its geometric shape. The cone does not flex or deform regardless of input power and frequency. Dual Super-Spider with composite center and symmetric stitched tinsel leads The Subzero spider is of the super spider type, which means the spider has the same diameter as the cone -this ensures the spider is not limiting excursion. The Subzero is equipped with a double super spider unit comprised of a Nomax /Romax hybrid material that has been epoxy coated for increased strength. The individual super spider units are arranged as identical opposites - canceling nonlinearities inherent to typical single or dual spider designs.The result is a clean sound - free from mechanical artifacts. For optimal performance the edge suspension and spider must have the same excursion potential, this is not possible with a traditional spider of limited diameter. Traditionally, the spider is glued to the voice coil, this results in heat transfer from the voice coil to the spider. This heat transfer effects the spiders compliance and can over time degrade the spider. The Subzero super spider is not glued the voice coil, but attached to a composite center ring that in turn is bonded to the voice coil. The special composite material is neither heat sensitive nor a thermal conductor. Thus the endurance and longevity of the Subzero is not affected regardless of drive level. The tinsel leads to the voice coil are sewn into the spider to ensure against collision with the cone during extreme excursion. This also extends the life of the tinsel leads, as they now bend more gently over a longer distance. The symmetrical design of the tinsel leads prevents an asymmetrical pull on the cone. The result is longer woofer life, and greater endurance. Double stacked Cobalt-Ceramic high gauss magnet system Subzero is built around a gigantic magnet system. It consists of two huge Cobalt-Ceramic magnets which have been hyper magnetised in-house by Earthquakes military grade Magnetiser. The two magnets have a total thickness of 6 cm, the top plate alone is 1 cm and the pole piece is 5 cm. With a total height of 12 cm - the voice coil is given unhindered travel space far beyond its mechanical limits. This ensures that not even the strongest transient may cause the device to run out of electromagnetic coupling. At the same time the high gap height contributes to voice coil cooling, as the immense mass of metal effectively absorbs heat. Diamond cut chassis with XLT geometry The Subzero is based on Earthquakes signature XLT chassis geometry. It is the optimal design for extreme excursion. The XLT chassis allows for extra length between the spider (center suspension) and the magnetic gap. It is designed to accommodate oversized spiders and voice coils. The Subzero chassis feature another advanced design detail unique to the Subzero. All other woofers have the chassis mounted on top of the magnet. The Subzero encases the magnet within the chassis and the chassis is mounted to the magnet from behind. This special design prevents the chassis from degrading the magnetic flux asserted on the voice coil. The oversized and rigid chassis is made of cast aluminum which is then diamond cut. This results in an ultra-rigid and robust chassis featuring stunning good looks. The chassis is further characterized by all components of the assembly being bolted together with stainless steel machine screws. This design is extremely rugged compared to ordinary assemblies where the chassis and magnet system is often glued and / or tabbed together. The technically superior design ensures exceptional durability, sound quality and pride of ownership. Pris er pr. stk. Specifications: Model: Subzero-12 EAN: 1-1411168-975921 Size: 12" Fs: 26.8Hz Max Power: 2000W RMS Power: 1000W Mechanical Xmax = 3.5"/88.9mm peak to peak Electrical Xmax = 2"/50.8mm peak to peak Impedance: dual 4Ω Sensitivity:85.9dB Dual Nomax / Romax spider 8 gauge speaker terminals Patented PSP terminal BL 70% @ Xmech Dimensions: Diameter: 336mm Cut-Out Diameter: 292mm Mounting Diameter: 195mm TS Parameters: TS data obtained using the VI-BOX high power system. Specs measured @ 100watt rms. Standard TS is done @ 1-3 watt, insufficient for obtaining true data in a high excursion modern woofer. Fmd= 3.0000 KA Qmd= 1.0000 Flp= 8.0000 KA Qlp= 2.0000 Znom= 8.0000 Ohm Revc= 7.7000 Ohm Sd= 53.0000E-3 M² Mmd= 236.4970E-3 Kg Rtvc= 250.0000E-3 °C/W Xcoil= 3.0000 In Krm= 35.5980E-3 Ohm Erm= 805.0000E-3 Kxm= 237.3670E-3 H Exm= 672.0000E-3 Rms= 3.7712 N·S/M Mms= 243.5090E-3 Kg Cms= 144.8275E-6 M/N Vas= 2.0520 Ft³ Fo= 26.8001 Hz Qms= 10.8730 Qes= 0.4411 Qts= 0.4239 BL= 26.7542 T·M Levc= 13.4777E-3 H SPLo= 85.8761 dB No= 243.1000E-3 %
5.699,00 kr
-
Earthquake Earthquake DBXi-15D 15" Subwoofer - Kraftfuld Bas & Præcision
DBXi – højtydende subwooferenheder med avanceret teknologi. DBXi er en showcase for anvendelse og adaptering af ekstremt avanceret teknologi. Earthquakes unikke DBXi enheder repræsenterer en ny kategori af basenheder. DBXi gør valget for den seriøse selvbygger enkelt. Det er nu ikke længere nødvendigt at beslutte om subwooferen skal gå dybt med høj SPL eller være hurtig, præcis og musikalsk. Innovativ teknologi og revolutionerende bearbejdningsproces er kendetegnet i DBXi’s konstruktion. De har muliggjort fremstillingen af en subwooferenhed der kan levere tordnende høj kælderdyb bas med hurtighed, præcision og detaljer.Udviklingen af DBXi Udviklingen af de nye DBXi subwoofer enheder begyndte med en dybdegående revision af samtlige elementer i subwoofer design. Konklusionen blev at en forfining af eksisterende teknologi ikke kunne overkomme de kendte begrænsninger. Ny teknologi var en nødvendighed for at kunne præstere knogleknusende lavfrekvent respons og samtidig gå op i det nedre mellemtone område. Mange fabrikanter er i stand til at lave tunge og langsomme enheder der begynder at snuble over sig selv allerede ved 65 – 70 Hz. Ligeledes er mange fabrikanter i stand til at fremstille forvoksede mellemtoner der er hurtige, men ikke er i stand til at gå dybere end 60 Hz. Et af de helt store designkrav til DBXi var en lineær frekvensrespons fra 20 – 250 Hz (15” DBXi). Det der adskiller fantastiske subwooferenheder fra middelmådige, er paradoksalt nok deres evne til at gengive de højere frekvenser. Især ved musikgengivelse er en hurtig og hårdtslående bas meget mere medrivende end en bas som føles tung og langsom. En bas skal slå musikkens rytme an, ikke komme efter den.Magnetsystem baseret på nuklear teknologi DBXi’s ultra kraftige magnetsystem er resultatet af et usædvanligt samarbejde med atomkraft industrien i Wisconsin. For at opnå den ønskede motorkraft var det nødvendigt at øge styrken markant i forhold til traditionelle magneter. Dette indledte et samarbejde med en fabrikant af plutonium fuel rods (radioaktiv brændstofs cylindre til atomkraftsværk) i Wisconsin. Denne fabrikant havde opfundet en særlig varmsmedning (hot forging) proces, der muliggjorde fremstillingen af motorens bagplade og centerdel ud af et stykke. Gennem et længere samarbejde lykkedes det at videreudvikle fuel rod forging teknologien for fremstilling af super gauss koncentrerede magnetsystemer. Den ultra høje magnetiske intensitet opnås ved at alle magnetens feltlinier nu kan overføre magnetisk flux tabsfrit, da hele magnetstrukturen er et stykke i stedet for af flere som traditionelt. Det giver en ekstremt effektiv og præcis motor. Højtydende svingspole med patenteret turbinekøling I hjertet af DBXi sidder en overdimensioneret ultra seriøs svingspole. Alle aspekter ved svingspolens konstruktion er optimeret for maksimal ydelse, holdbarhed og lydkvalitet. Svingspole formeren (den cylinder svingspolen vikles på) er fremstillet af aluminium bobbin og ikke pap, Kapton® eller glasfiber. Brugen af aluminium bobbin sikrer at der ikke opstår hotspots på svingspolen takket være aluminiums gode varmelednings evne. Brugen af aluminium bobbin forvandler dermed hele svingspolen til en stor køleprofil der sikrer en jævn spredning af varmen, hvilket øger belastbarheden betydeligt. Svingspolen er viklet af kobber firkanttråd, brugen af firkanttråd forøger svingspolens køleevne betydeligt. Firkanttråd har et større overfladeareal end almindelig rund tråd og kan derfor afsætte væsentlig mere varme. Firkanttråd har også den fordel at spolen kan vikles tættere, hvilket øger motorkraften.Enheden er udstyret med Earthquakes patenterede TCT (Turbine Cooled Transducer) teknologi. TCT skaber en tornado-lignende kølende luftstrøm omkring svingspolen, der øges i intensitet med slaglængden. Tornadoen skabes ved at luft tvinges igennem kølekanaler, der er fræset i en hvirvel struktur. Traditionel svingspole køling gøres ved at polstykket er udboret og enhedens vandring skubber luft frem og tilbage, køleeffekten har her kun en lineær stigning som funktion af enhedens vandring. TCT er anderledes. Earthquakes unikke TCT (Turbine Cooled Transducer) skaber en eksponentiel stigning i køleeffekt, som funktion af enhedens vandring. Dette opnås ved at udnytte centrifugale kræfter i den roterende luft. TCT er så effektivt at svingspolens temperatur er nedsat med 50 % i forhold til samme motor uden TCT. Når en subwooferenhed belastes og dens vandring øges stiger svingspolens temperatur, dette leder til kompression. Kompressionen er et resultat af den stigende elektriske modstand i svingspolen, jo højere temperatur jo højere modstand. Da TCT’s køleevne stiger eksponentielt med enhedens vandring undgås varmeafledt kompression.Specialdesignet membran og ophæng for enorm vandring En magnet i verdensklasse og overdimensioneret svingspole kommer kun til sin ret hvis enheden kan tåle at bevæge sig. Til DBXi blev der udviklet et særligt SWE (Super Wide Edge) kantophæng med en højde på 31 mm. Kantophænget er af enkeltlags (single layer) typen, der er termisk presset og lamineret for ekstrem styrke og mobilitet. Det tillader membranvandring på mere end 62 mm uden deformation eller øget vandringsmodstand. Det sikrer at selv de kraftigste impulser bliver gengivet med perfekt, hurtig og præcis transientrespons. DBXi membranen er fremstillet af et specielt poly-injectet materiale der opnår yderligere stivhed ved sin geometriske udformning. Membranen hverken flexer eller deformerer uanset inputstyrke og frekvens. DBXi spideren er af superspider typen, hvilket betyder at spideren har samme diameter som membranen. Det sikrer at spideren ikke er vandringsbegrænsende, som det er tilfældet ved de fleste andre fabrikanters konstruktioner. For at opnå optimal ydelse skal kantophænget og spideren have samme vandringspotentiale, dette er ikke muligt ved en traditionel spider af begrænset diameter. Litzetrådene til svingspolens strømforsyning er indsyet i spideren for at sikre imod kollidering med membranen. Indsyningen forlænger også litzetrådenes levetid, da de nu bevæger sig ens over en længere afstand. Produkt Dimensioner Diameter 395 mm Cut out hole 372 mm Mounting Depth 202 mm Magnet Width / Diameter 190 mm Prisen er pr. stk. Specifikationer: Model: DBXi-15D EAN: 1-110968-975940 Anbefalet forstærker effekt: 750 - 2000-Watts Fs: 12 Hz Xmax: 4" Effiktivitet (1W/1M): 88 dB SPL Nominel impedans: Dual 4 ohm 15" cast subwoofer Dobbelt svingspole 2 x 4-ohm 3" svingspole af aluminum bobin 150 Oz dobelt stakket magnet Xmax 74 mm P-P Xmech 98 mm P-P BL 60 % @ Xmech TS Parametre:TS data obtained using the VI-BOX high power system. Specs measured @ 100watt rms. Standard TS is done @ 1-3 watt, insufficient for obtaining true data in a high excursion modern woofer. Fmd= 3.0000 KA Qmd= 1.0000 Flp= 8.0000 KA Qlp= 2.0000 Znom= 8.0000 Ohm Revc= 6.6000 Ohm Sd= 89.0000E-3 M² Mmd= 211.3830E-3 Kg Rtvc= 250.0000E-3 °C/W Xcoil= 2.0000 In Krm= 187.0000E-3 Ohm Erm= 406.0000E-3 Kxm= 4.8620 H Exm= 0.0000 Rms= 27.6376 N·S/M Mms= 226.6500E-3 Kg Cms= 127.0500E-6 M/N Vas= 5.0470 Ft³ Fo= 13.5757 Hz Qms= 2.6790 Qes= 1.0470 Qts= 0.4910 BL= 16.3200 T·M Levc= 773.8113E-6 H SPLo= 87.3776 dB No= 343.5075E-3 %
3.299,00 kr
-
Earthquake Earthquake DBXI-12D 12" Subwoofer - Dyb Bas & Høj Præcision
DBXi – højtydende subwooferenheder med avanceret teknologi.DBXi er en showcase for anvendelse og adaptering af ekstremt avanceret teknologi. Earthquakes unikke DBXi enheder repræsenterer en ny kategori af basenheder. DBXi gør valget for den seriøse selvbygger enkelt. Det er nu ikke længere nødvendigt at beslutte om subwooferen skal gå dybt med høj SPL eller være hurtig, præcis og musikalsk. Innovativ teknologi og revolutionerende bearbejdningsproces er kendetegnet i DBXi’s konstruktion. De har muliggjort fremstillingen af en subwooferenhed der kan levere tordnende høj kælderdyb bas med hurtighed, præcision og detaljer.Udviklingen af DBXi Udviklingen af de nye DBXi subwoofer enheder begyndte med en dybdegående revision af samtlige elementer i subwoofer design. Konklusionen blev at en forfining af eksisterende teknologi ikke kunne overkomme de kendte begrænsninger. Ny teknologi var en nødvendighed for at kunne præstere knogleknusende lavfrekvent respons og samtidig gå op i det nedre mellemtone område. Mange fabrikanter er i stand til at lave tunge og langsomme enheder der begynder at snuble over sig selv allerede ved 65 – 70 Hz. Ligeledes er mange fabrikanter i stand til at fremstille forvoksede mellemtoner der er hurtige, men ikke er i stand til at gå dybere end 60 Hz. Et af de helt store designkrav til DBXi var en lineær frekvensrespons fra 20 – 250 Hz (15” DBXi). Det der adskiller fantastiske subwooferenheder fra middelmådige, er paradoksalt nok deres evne til at gengive de højere frekvenser. Især ved musikgengivelse er en hurtig og hårdtslående bas meget mere medrivende end en bas som føles tung og langsom. En bas skal slå musikkens rytme an, ikke komme efter den.Magnetsystem baseret på nuklear teknologi DBXi’s ultra kraftige magnetsystem er resultatet af et usædvanligt samarbejde med atomkraft industrien i Wisconsin. For at opnå den ønskede motorkraft var det nødvendigt at øge styrken markant i forhold til traditionelle magneter. Dette indledte et samarbejde med en fabrikant af plutonium fuel rods (radioaktiv brændstofs cylindre til atomkraftsværk) i Wisconsin. Denne fabrikant havde opfundet en særlig varmsmedning (hot forging) proces, der muliggjorde fremstillingen af motorens bagplade og centerdel ud af et stykke. Gennem et længere samarbejde lykkedes det at videreudvikle fuel rod forging teknologien for fremstilling af super gauss koncentrerede magnetsystemer. Den ultra høje magnetiske intensitet opnås ved at alle magnetens feltlinier nu kan overføre magnetisk flux tabsfrit, da hele magnetstrukturen er et stykke i stedet for af flere som traditionelt. Det giver en ekstremt effektiv og præcis motor. Højtydende svingspole med patenteret turbinekøling I hjertet af DBXi sidder en overdimensioneret ultra seriøs svingspole. Alle aspekter ved svingspolens konstruktion er optimeret for maksimal ydelse, holdbarhed og lydkvalitet. Svingspole formeren (den cylinder svingspolen vikles på) er fremstillet af aluminium bobbin og ikke pap, Kapton® eller glasfiber. Brugen af aluminium bobbin sikrer at der ikke opstår hotspots på svingspolen takket være aluminiums gode varmelednings evne. Brugen af aluminium bobbin forvandler dermed hele svingspolen til en stor køleprofil der sikrer en jævn spredning af varmen, hvilket øger belastbarheden betydeligt. Svingspolen er viklet af kobber firkanttråd, brugen af firkanttråd forøger svingspolens køleevne betydeligt. Firkanttråd har et større overfladeareal end almindelig rund tråd og kan derfor afsætte væsentlig mere varme. Firkanttråd har også den fordel at spolen kan vikles tættere, hvilket øger motorkraften.Enheden er udstyret med Earthquakes patenterede TCT (Turbine Cooled Transducer) teknologi. TCT skaber en tornado-lignende kølende luftstrøm omkring svingspolen, der øges i intensitet med slaglængden. Tornadoen skabes ved at luft tvinges igennem kølekanaler, der er fræset i en hvirvel struktur. Traditionel svingspole køling gøres ved at polstykket er udboret og enhedens vandring skubber luft frem og tilbage, køleeffekten har her kun en lineær stigning som funktion af enhedens vandring. TCT er anderledes. Earthquakes unikke TCT (Turbine Cooled Transducer) skaber en eksponentiel stigning i køleeffekt, som funktion af enhedens vandring. Dette opnås ved at udnytte centrifugale kræfter i den roterende luft. TCT er så effektivt at svingspolens temperatur er nedsat med 50 % i forhold til samme motor uden TCT. Når en subwooferenhed belastes og dens vandring øges stiger svingspolens temperatur, dette leder til kompression. Kompressionen er et resultat af den stigende elektriske modstand i svingspolen, jo højere temperatur jo højere modstand. Da TCT’s køleevne stiger eksponentielt med enhedens vandring undgås varmeafledt kompression.Specialdesignet membran og ophæng for enorm vandring En magnet i verdensklasse og overdimensioneret svingspole kommer kun til sin ret hvis enheden kan tåle at bevæge sig. Til DBXi blev der udviklet et særligt SWE (Super Wide Edge) kantophæng med en højde på 31 mm. Kantophænget er af enkeltlags (single layer) typen, der er termisk presset og lamineret for ekstrem styrke og mobilitet. Det tillader membranvandring på mere end 62 mm uden deformation eller øget vandringsmodstand. Det sikrer at selv de kraftigste impulser bliver gengivet med perfekt, hurtig og præcis transientrespons. DBXi membranen er fremstillet af et specielt poly-injectet materiale der opnår yderligere stivhed ved sin geometriske udformning. Membranen hverken flexer eller deformerer uanset inputstyrke og frekvens. DBXi spideren er af superspider typen, hvilket betyder at spideren har samme diameter som membranen. Det sikrer at spideren ikke er vandringsbegrænsende, som det er tilfældet ved de fleste andre fabrikanters konstruktioner. For at opnå optimal ydelse skal kantophænget og spideren have samme vandringspotentiale, dette er ikke muligt ved en traditionel spider af begrænset diameter. Litzetrådene til svingspolens strømforsyning er indsyet i spideren for at sikre imod kollidering med membranen. Indsyningen forlænger også litzetrådenes levetid, da de nu bevæger sig ens over en længere afstand. Prisen er pr. stk. Specifikationer: Model: DBXi-12D EAN: 1-114689-759865 Model: DBXi-12 EAN: 1-113689-759868 Anbefalet forstærker effekt: 500 - 1500-Watts Fs: 16 Hz Effiktivitet (1W/1M): 87 dB SPL Nominel impedans: Dual 4 ohm 12" cast subwoofer Dobbelt svingspole 2 x 4-ohm 2" svingspole af aluminum bobin 140 Oz dobelt stakket magnet Xmax 66 mm P-P Xmech 88 mm P-P BL 60 % @ Xmech TS Parametre:TS data obtained using the VI-BOX high power system. Specs measured @ 100watt rms. Standard TS is done @ 1-3 watt, insufficient for obtaining true data in a high excursion modern woofer. Fmd= 3.0000 KA Qmd= 1.0000 Flp= 8.0000 KA Qlp= 2.0000 Znom= 8.0000 Ohm Revc= 6.4000 Ohm Sd= 55.0000E-3 M² Mmd= 194.6390E-3 Kg Rtvc= 250.0000E-3 °C/W Xcoil= 1.5000 In Krm= 182.3750E-3 Ohm Erm= 439.0000E-3 Kxm= 4.4910 H Exm= 0.0000 Rms= 27.6376 N·S/M Mms= 202.0516E-3 Kg Cms= 191.6562E-6 M/N Vas= 2.9243 Ft³ Fo= 17.5757 Hz Qms= 1.1748 Qes= 0.9993 Qts= 0.5400 BL= 14.4200 T·M Levc= 714.7648E-6 H SPLo= 83.2535 dB No= 132.9000E-3 %
2.599,00 kr
-
Earthquake Earthquake TremorX-15-4 Subwoofer | Høj Ydelse & Kvalitet
TremorX Rationel, slagkraftig og præcis subwoofer enhed. TremorX er Earthquakes value performance leder. Alle aspekter af dens konstruktion er gennemrationaliseret og optimeret til mindste detalje. Intet overflødigt er tilføjet og intet væsentligt er fjernet. Flere nøgle teknologier fra de dyrere Earthquake subwoofer serier er nedarvet i TremorX. Resultat er en subwoofer enhed uden sammenligning i sin klasse. Avanceret og rationel inhouse produktion af TremorX giver disse opsigtsvækkende egenskaber til en uhørt lav pris. TremorX er bevis på at lav pris og høj kvalitet kan sameksistere. Nøgtern gennemgang og funktions rationalisering frem for kvalitets reducering er nøgleord for TremorXs konstruktion. Med Avancerede Earthquake teknologier som TCT (Turbine Cooled Transducer), XLT chassis, Mill-Temp Aluminium svingspole, Dual Symmetrical stitched Power Leeds og WE (Wide Edge) kantophæng. Står TremorX ikke tilbage for noget. Solid kvalitet og raffineret teknisk konstruktion gør TremorX til en klart valg for den pris og performance orienterede selvbygger. Mill-Temp Aluminium svingspoleI hjertet af TremorX sidder en overdimensioneret svingspole. Alle aspekter ved svingspolens konstruktion er optimeret for maksimal ydelse, holdbarhed og lydkvalitet. Svingspole formeren (den cylinder svingspolen vikles på) er fremstillet af aluminium og ikke pap, Kapton® eller glasfiber. Brugen af aluminium sikrer at der ikke opstår hotspots på svingspolen takket være aluminiums gode varmelednings evne. Brugen af aluminium forvandler dermed hele svingspolen til en stor køleprofil der sikrer en jævn spredning af varmen, hvilket øger belastbarheden betydeligt. Svingspolen er viklet af kobbertråd, Svingspolens konstruktion lever op til mil-spec standarten for temperatur bestandighed. Dette garanterer at svingspolen yder optimalt selv ved hård og vedvarende drift TCT - Turbine Cooled Transducer TremorX er udstyret med Earthquakes patenterede TCT (Turbine Cooled Transducer) teknologi. TCT skaber en tornado-lignende kølende luftstrøm omkring svingspolen, der øges i intensitet med slaglængden. Tornadoen skabes ved at luft tvinges igennem kølekanaler, der er fræset i en hvirvel struktur. Traditionel svingspole køling gøres ved at polstykket er udboret og enhedens vandring skubber luft frem og tilbage, køleeffekten har her kun en lineær stigning som funktion af enhedens vandring. TCT er anderledes. Earthquakes unikke TCT (Turbine Cooled Transducer) skaber en eksponentiel stigning i køleeffekt, som funktion af enhedens vandring. Dette opnås ved at udnytte centrifugale kræfter i den roterende luft. TCT er så effektivt at svingspolens temperatur er nedsat med 50 % i forhold til samme motor uden TCT. Når en subwooferenhed belastes og dens vandring øges stiger svingspolens temperatur, dette leder til kompression. Kompressionen er et resultat af den stigende elektriske modstand i svingspolen, jo højere temperatur jo højere modstand. Da TCT’s køleevne stiger eksponentielt med enhedens vandring undgås varmeafledt kompression. WE –Wide Edge ophæng TremorXs særlige Wide Edge kantophæng muliggør enorm vandring uden deformation og øget modstand. Kantophænget er af enkeltlags (single layer) typen, der er termisk presset for ekstrem styrke og mobilitet. Det tillader membranvandring på mere end 35 mm uden deformation eller øget vandringsmodstand. Det sikrer at selv de kraftigste impulser bliver gengivet med perfekt, hurtig og præcis transientrespons. TX Blacktop membranTremorX membranen er fremstillet af et specielt poly-injectet materiale der opnår yderligere stivhed ved sin geometriske udformning. Membranen hverken flekser eller deformerer uanset inputstyrke og frekvens. Dual Symmetrical Stitched Tensile LeedsLitzetrådene til svingspolens strømforsyning er indsyet i spideren for at sikre imod kollidering med membranen. Indsyningen forlænger også litzetrådenes levetid, da de nu bevæger sig ens over en længere afstand. TremorXs har særlige symmetriske litzetråds indsyning så litzetrådenes compliance ikke påvirker enheden asymmetrisk. Dette optimerer enhedens respons og sikrer lang holdbarhed selv ved meget hård drift, da svingspolen bevæger sig helt lige i magnetgabet. XLT chassisTremorX er opbygget på Earthquakes XLT chassis struktur i støbt aluminium. Det er optimeret til TremorXs lange svingspole og kraftige magnet. Det er vigtigt at chassiset tillader tilstrækkelig længde mellem spider (center ophæng) og magnetgab. For at opnå TremorXs høje ydelse og belastbarhed er det nødvendigt at svingspolen er meget høj, dette udelukker brugen af billige standart chassiser. Ved en optimal konstruktion er helheden altid mere end summen af enkeltdelene. Den optimale XLT chassis struktur i samarbejde med membranen, ophænget, magneten og den kraftige svingspole sikrer dette perfekte harmonisk sammenspil. TremorX – Høj Ydelse - Høj kvalitet – Stærk pris Pris er pr. stk. Features: Heavy duty stitched leads Spring loaded speaker connections Anti-wobble cone construction TCT Technology (Turbine Cooled Transducer) for high efficiency output Military grade single 4-Ohm or single 8-Ohm voice coil options
1.197,00 kr
-
Earthquake Earthquake TremorX-12-4 1250W Subwoofer - Kraftig & Præcis Bas
TremorX Rationel, slagkraftig og præcis subwoofer enhed. TremorX er Earthquakes value performance leder. Alle aspekter af dens konstruktion er gennemrationaliseret og optimeret til mindste detalje. Intet overflødigt er tilføjet og intet væsentligt er fjernet. Flere nøgle teknologier fra de dyrere Earthquake subwoofer serier er nedarvet i TremorX. Resultat er en subwoofer enhed uden sammenligning i sin klasse. Avanceret og rationel inhouse produktion af TremorX giver disse opsigtsvækkende egenskaber til en uhørt lav pris. TremorX er bevis på at lav pris og høj kvalitet kan sameksistere. Nøgtern gennemgang og funktions rationalisering frem for kvalitets reducering er nøgleord for TremorXs konstruktion. Med Avancerede Earthquake teknologier som TCT (Turbine Cooled Transducer), XLT chassis, Mill-Temp Aluminium svingspole, Dual Symmetrical stitched Power Leeds og WE (Wide Edge) kantophæng. Står TremorX ikke tilbage for noget. Solid kvalitet og raffineret teknisk konstruktion gør TremorX til en klart valg for den pris og performance orienterede selvbygger. Mill-Temp Aluminium svingspoleI hjertet af TremorX sidder en overdimensioneret svingspole. Alle aspekter ved svingspolens konstruktion er optimeret for maksimal ydelse, holdbarhed og lydkvalitet. Svingspole formeren (den cylinder svingspolen vikles på) er fremstillet af aluminium og ikke pap, Kapton® eller glasfiber. Brugen af aluminium sikrer at der ikke opstår hotspots på svingspolen takket være aluminiums gode varmelednings evne. Brugen af aluminium forvandler dermed hele svingspolen til en stor køleprofil der sikrer en jævn spredning af varmen, hvilket øger belastbarheden betydeligt. Svingspolen er viklet af kobbertråd, Svingspolens konstruktion lever op til mil-spec standarten for temperatur bestandighed. Dette garanterer at svingspolen yder optimalt selv ved hård og vedvarende drift TCT - Turbine Cooled Transducer TremorX er udstyret med Earthquakes patenterede TCT (Turbine Cooled Transducer) teknologi. TCT skaber en tornado-lignende kølende luftstrøm omkring svingspolen, der øges i intensitet med slaglængden. Tornadoen skabes ved at luft tvinges igennem kølekanaler, der er fræset i en hvirvel struktur. Traditionel svingspole køling gøres ved at polstykket er udboret og enhedens vandring skubber luft frem og tilbage, køleeffekten har her kun en lineær stigning som funktion af enhedens vandring. TCT er anderledes. Earthquakes unikke TCT (Turbine Cooled Transducer) skaber en eksponentiel stigning i køleeffekt, som funktion af enhedens vandring. Dette opnås ved at udnytte centrifugale kræfter i den roterende luft. TCT er så effektivt at svingspolens temperatur er nedsat med 50 % i forhold til samme motor uden TCT. Når en subwooferenhed belastes og dens vandring øges stiger svingspolens temperatur, dette leder til kompression. Kompressionen er et resultat af den stigende elektriske modstand i svingspolen, jo højere temperatur jo højere modstand. Da TCT’s køleevne stiger eksponentielt med enhedens vandring undgås varmeafledt kompression. WE –Wide Edge ophæng TremorXs særlige Wide Edge kantophæng muliggør enorm vandring uden deformation og øget modstand. Kantophænget er af enkeltlags (single layer) typen, der er termisk presset for ekstrem styrke og mobilitet. Det tillader membranvandring på mere end 35 mm uden deformation eller øget vandringsmodstand. Det sikrer at selv de kraftigste impulser bliver gengivet med perfekt, hurtig og præcis transientrespons. TX Blacktop membranTremorX membranen er fremstillet af et specielt poly-injectet materiale der opnår yderligere stivhed ved sin geometriske udformning. Membranen hverken flekser eller deformerer uanset inputstyrke og frekvens. Dual Symmetrical Stitched Tensile LeedsLitzetrådene til svingspolens strømforsyning er indsyet i spideren for at sikre imod kollidering med membranen. Indsyningen forlænger også litzetrådenes levetid, da de nu bevæger sig ens over en længere afstand. TremorXs har særlige symmetriske litzetråds indsyning så litzetrådenes compliance ikke påvirker enheden asymmetrisk. Dette optimerer enhedens respons og sikrer lang holdbarhed selv ved meget hård drift, da svingspolen bevæger sig helt lige i magnetgabet. XLT chassisTremorX er opbygget på Earthquakes XLT chassis struktur i støbt aluminium. Det er optimeret til TremorXs lange svingspole og kraftige magnet. Det er vigtigt at chassiset tillader tilstrækkelig længde mellem spider (center ophæng) og magnetgab. For at opnå TremorXs høje ydelse og belastbarhed er det nødvendigt at svingspolen er meget høj, dette udelukker brugen af billige standart chassiser. Ved en optimal konstruktion er helheden altid mere end summen af enkeltdelene. Den optimale XLT chassis struktur i samarbejde med membranen, ophænget, magneten og den kraftige svingspole sikrer dette perfekte harmonisk sammenspil. TremorX – Høj Ydelse - Høj kvalitet – Stærk pris Pris er pr. stk. Features: Heavy duty stitched leads Spring loaded speaker connections Anti-wobble cone construction TCT Technology (Turbine Cooled Transducer) for high efficiency output Military grade single 4-Ohm or single 8-Ohm voice coil options Specifications: Model: TremorX-12-4 EAN: 1-112468-975970 Size: 12" Fs: 29.1094 Hz Max Power: 1250W Impedance: 4Ω Sensitivity:86.97dB Qes: 0.617 Qms: 5.794 Qts: 0.5576
1.115,00 kr
-
Earthquake Earthquake TremorX-10 Kraftfuld Subwoofer - Slagkraftig Lyd 1000W
TremorX Rationel, slagkraftig og præcis subwoofer enhed. TremorX er Earthquakes value performance leder. Alle aspekter af dens konstruktion er gennemrationaliseret og optimeret til mindste detalje. Intet overflødigt er tilføjet og intet væsentligt er fjernet. Flere nøgle teknologier fra de dyrere Earthquake subwoofer serier er nedarvet i TremorX. Resultat er en subwoofer enhed uden sammenligning i sin klasse. Avanceret og rationel inhouse produktion af TremorX giver disse opsigtsvækkende egenskaber til en uhørt lav pris. TremorX er bevis på at lav pris og høj kvalitet kan sameksistere. Nøgtern gennemgang og funktions rationalisering frem for kvalitets reducering er nøgleord for TremorXs konstruktion. Med Avancerede Earthquake teknologier som TCT (Turbine Cooled Transducer), XLT chassis, Mill-Temp Aluminium svingspole, Dual Symmetrical stitched Power Leeds og WE (Wide Edge) kantophæng. Står TremorX ikke tilbage for noget. Solid kvalitet og raffineret teknisk konstruktion gør TremorX til en klart valg for den pris og performance orienterede selvbygger. Mill-Temp Aluminium svingspoleI hjertet af TremorX sidder en overdimensioneret svingspole. Alle aspekter ved svingspolens konstruktion er optimeret for maksimal ydelse, holdbarhed og lydkvalitet. Svingspole formeren (den cylinder svingspolen vikles på) er fremstillet af aluminium og ikke pap, Kapton® eller glasfiber. Brugen af aluminium sikrer at der ikke opstår hotspots på svingspolen takket være aluminiums gode varmelednings evne. Brugen af aluminium forvandler dermed hele svingspolen til en stor køleprofil der sikrer en jævn spredning af varmen, hvilket øger belastbarheden betydeligt. Svingspolen er viklet af kobbertråd, Svingspolens konstruktion lever op til mil-spec standarten for temperatur bestandighed. Dette garanterer at svingspolen yder optimalt selv ved hård og vedvarende drift TCT - Turbine Cooled Transducer TremorX er udstyret med Earthquakes patenterede TCT (Turbine Cooled Transducer) teknologi. TCT skaber en tornado-lignende kølende luftstrøm omkring svingspolen, der øges i intensitet med slaglængden. Tornadoen skabes ved at luft tvinges igennem kølekanaler, der er fræset i en hvirvel struktur. Traditionel svingspole køling gøres ved at polstykket er udboret og enhedens vandring skubber luft frem og tilbage, køleeffekten har her kun en lineær stigning som funktion af enhedens vandring. TCT er anderledes. Earthquakes unikke TCT (Turbine Cooled Transducer) skaber en eksponentiel stigning i køleeffekt, som funktion af enhedens vandring. Dette opnås ved at udnytte centrifugale kræfter i den roterende luft. TCT er så effektivt at svingspolens temperatur er nedsat med 50 % i forhold til samme motor uden TCT. Når en subwooferenhed belastes og dens vandring øges stiger svingspolens temperatur, dette leder til kompression. Kompressionen er et resultat af den stigende elektriske modstand i svingspolen, jo højere temperatur jo højere modstand. Da TCT’s køleevne stiger eksponentielt med enhedens vandring undgås varmeafledt kompression. WE –Wide Edge ophæng TremorXs særlige Wide Edge kantophæng muliggør enorm vandring uden deformation og øget modstand. Kantophænget er af enkeltlags (single layer) typen, der er termisk presset for ekstrem styrke og mobilitet. Det tillader membranvandring på mere end 35 mm uden deformation eller øget vandringsmodstand. Det sikrer at selv de kraftigste impulser bliver gengivet med perfekt, hurtig og præcis transientrespons. TX Blacktop membranTremorX membranen er fremstillet af et specielt poly-injectet materiale der opnår yderligere stivhed ved sin geometriske udformning. Membranen hverken flekser eller deformerer uanset inputstyrke og frekvens. Dual Symmetrical Stitched Tensile LeedsLitzetrådene til svingspolens strømforsyning er indsyet i spideren for at sikre imod kollidering med membranen. Indsyningen forlænger også litzetrådenes levetid, da de nu bevæger sig ens over en længere afstand. TremorXs har særlige symmetriske litzetråds indsyning så litzetrådenes compliance ikke påvirker enheden asymmetrisk. Dette optimerer enhedens respons og sikrer lang holdbarhed selv ved meget hård drift, da svingspolen bevæger sig helt lige i magnetgabet. XLT chassisTremorX er opbygget på Earthquakes XLT chassis struktur i støbt aluminium. Det er optimeret til TremorXs lange svingspole og kraftige magnet. Det er vigtigt at chassiset tillader tilstrækkelig længde mellem spider (center ophæng) og magnetgab. For at opnå TremorXs høje ydelse og belastbarhed er det nødvendigt at svingspolen er meget høj, dette udelukker brugen af billige standart chassiser. Ved en optimal konstruktion er helheden altid mere end summen af enkeltdelene. Den optimale XLT chassis struktur i samarbejde med membranen, ophænget, magneten og den kraftige svingspole sikrer dette perfekte harmonisk sammenspil. TremorX – Høj Ydelse - Høj kvalitet – Stærk pris Pris er pr. stk. Features: Heavy duty stitched leads Spring loaded speaker connections Anti-wobble cone construction TCT Technology (Turbine Cooled Transducer) for high efficiency output Military grade single 4-Ohm or single 8-Ohm voice coil options Specifications: Model: TremorX-10-4 EAN: 1-110468-975921 Size: 10" Fs: 30.97Hz Max Power: 1000W Impedance: 4Ω Sensitivity:86.4dB Qes: 0.372 Qms: 5.11 Qts: 0.3468
869,00 kr
-
Earthquake Earthquake SWS-8Xi Shallow Woofer: Maks Lyd, Minimalt Plads 2Ω
Earthquake SWS-8Xi bas The Earthquake “SWS” - Shallow Woofer System- Provides more sound from less space with less power than any other woofer technology. The core technology of the SWS was pioneered by Earthquake Sound's President Joseph Sahyoun and is now protected by multiple global patents. The “SWS” design moves the flexible suspension components(cone & spider) to the side allowingthe motor to be elevated. This reduces the mounting depth of the speaker while enhancing excursion capability. More excursion (woofer movement) equals more sound.Upgrading to SWS is both attractive and simple :1. Direct factory drop-in replacement.2. Greatly enhanced sound quality. Enjoy a rich full bodied sound with articulation and dynamics rivaling home hifi audiophile systems.3. Plays louder and cleaner than standard woofer - using less power.4. Works perfectly with factory amplifier, while still capable of further SPL with upgraded amplifiers.The modern luxury car buyer expects all aspects of their vehicle to be thrilling and engaging. Thiselevates the expectations for the audio system as people now carry their music with them where ever they go - making comparisons easy. They want it to sound as good as it possibly can while being on the road. Preferably it should be so good in the car that the driver looks forward to both the ride and the music. With Earthquake SWS woofers the authentic and authoritative sound is always at the driver fingertips.Designing sound quality :“SWS” technology employs a patented ribbed cone that eliminates cone break-up distortion while maintaining a light moving mass. This keeps the woofer nimble, fast and accurate. This fast acoustic response makes the sound engaging and entices the listener to turn up the sound as it just sounds “finger snapping good”.Designing durability :“SWS” employs a revolutionary innovation that welds an aluminum voice coil to an aluminum dust cap thus turning it into a heat sink. This heat exchanger uses convection/ conduction to transfer the heat out of the box. This increases the woofer performances and ensures that heat derived compression never occurs.In short :The “SWS” will play louder and more accurate while using less power and taking up less space than any other woofer on the planet. Our most popular size is the SWS-8” as it is a direct drop-in BMW factory replacement for the woofers located under the front seats. Simply remove the seats and replace the factory woofers with the SWS-8 woofers to improve the sound quality.Earthquake Sound also produces the SWS-8Xi that has a 2Ω voice coil - the same impedance as the BMW factory speakers. Sold and priced per piece. Features: Low profile mount for placement anywhere 2-Ohm impedance Inverted style cone design for maximum excursion in shallow mount applications High temperature voice with heat-sink attachment NOMEX/ROMEX spider assembly Protected by 3 U.S. patents Aluminum Bobbin Optional Adapter Ring R8-SWS Adapter Ring R8-SWS (*sold per pair) Specifications: Model: SWS-8Xi EAN: 0-168975-910165 Size: 8" high performance sub Fs: 20Hz - 300Hz Max Power: 300W RMS Power: 150W Impedance: 2Ω Sensitivity: 86.7dB Qes: 1.503 Qms: 3.208 Qts: 1.023 Revc: 1.600Ohm Sd=22.000m M² Md=: 35.000 g BL: 4.277 T-M No: 0.056 % SPLo: 79.5 dB Vas: 606.164m Ft3 Cms= 249.747u M/N Krm= 479.808u Ohm Erm: 0.834 Mms: 73.753g Mmd: 71.877m Kg Kxm: 22.40m H Exm: 0.440 Dimensions: SWS-8Xi Installation SWS-8Xi Manual SWS-8Xi Product Release
1.330,00 kr
-
Earthquake Earthquake SWS-8X Bas: Høj Lydkvalitet og Kompakt Design
Lydkvalitet i højeste klasse - Earthquake SWS-8X Bas Earthquake SWS-8X Bas er en innovativ højttalerteknologi, der leverer mere lyd fra mindre plads med mindre strøm end andre højttalerteknologier. Patenterbeskyttet teknologi blev opfundet af Earthquake Sound's præsident Joseph Sahyoun. SWS-designet flytter de fleksible suspensionselementer (kurv og spindel) til siden, hvilket gør det muligt at hæve motoren. Dette reducerer monteringsdybden af højttaleren og forbedrer udvidelse-evnen. Jo større udvidelse (højttalers bevægelse), jo mere lyd. Opgradering til SWS er både attraktivt og enkelt: Direkte fabrikserstatning. Markant forbedret lydkvalitet med en rig og fuldendt lyd med præcision og dynamik, der kan konkurrere med hjemmets Hi-Fi audiophile-systemer. Afspiller højere og renere end standardhøjttaler med mindre strøm. Fungerer perfekt med fabriksforstærker og kan også give endnu højere SPL med opgraderet forstærker. Moderne luksusbilskøbere forventer, at alle aspekter af deres bil skal være spændende og engagerende, også lydsystemet. De bærer nemlig deres musik med sig overalt og vil have lyd, der lyder så godt som muligt i bilen. Højttalerne skal være så gode, at føreren glæder sig til både køreturen og musikken. Med Earthquake SWS højttalere er den autentiske og autoritative lyd altid lige ved hånden. Lydkvalitet design: SWS-teknologien bruger en patenteret ribbet kurv, der eliminerer kurvefejl og distorsion, mens den opretholder en let bevægelsesmængde. Dette gør højttaleren hurtig, smidig og præcis. Den hurtige akustiske respons gør lyden engagerende og frister lytteren til at skrue op for lyden, da det lyder "finger-snapping godt". Durabilitet design: SWS bruger en revolutionerende innovation, der svejser en aluminiumsvoksel til en aluminiumstøvkappe, hvilket gør den til en varmeafleder. Varmeudveksleren anvender konvektion/ledning til at overføre varmen ud af boksen. Dette øger højttalerens ydeevne og sikrer, at varme-komprimering aldrig opstå
1.330,00 kr
-
Monacor RBT-35SR Ribbon Diskant Højttalerpar - Livlig Lyd og Høj Følsomhed
RBT-35SR horn loaded bånddiskant med masser af liv. Denne bånddiskant er interessant da den ligger sig lidt mere over imod det livlige grundet dens horn ladning. Bånddiskanter kan nogle gange opleves som en anelse tilbagelænet til rytmisk musik, som gør at nogen vil holde sig til dome diskanter for at bevare det rette liv til Rock og Pop. Er man fasineret af båndende og godt kan li de rolige passager de kan levere, men stadig ønsker lidt fremtoning i de høje toner er RBT-35SR et virkelig dejligt blend. Hvis du kigger under produkt billedet og finder frekvens og impedans kurven, kan du se hvordan følsomheden stiger stødt fra 7KHz og helt op til 17KHz, og bevare gengivelse helt op til 30KHz. Når man tænker på hvor langt den strækker sig op igennem frekvens spektrummet er det virkelig bemærkelses værdigt at den kan deles ved 2500Hz og dermed mulig i en 2 vejs højttaler. De købes som et par, så prisen du ser er for 2 stk diskanter Videoen nedenfor viser RBT-20 og ikke RBT-35SR men det giver en ide om kvalitet Horn loaded var der nogen der sagde rørslæde, helt sikkert et godt match. Med en impedans trukket efter en lineal og 96dBs følsomhed, liv og varme til en lytter. The new high-end tweeters RBT-10, RBT-20 and RBT-35SR are part of the so-called real ribbon tweeters. The audio signal flows through the entire cone which is of extra low weight and consists of an aluminium film. A built-in high-quality transformer converts the low impedance of this cone into 5-8 Ω which is non-critical for the amplifier. Ribbon tweeters impress by an extra fine and brilliant reproduction of the high frequency range. Due to continuous further development, it is already possible to use these ribbon tweeters with crossover frequencies from 2,500 Hz on, depending on the type. This makes them a top choice whenever hi-fi speakers or studio monitors of the highest quality are required. Ribbon tweeters require a crossover network for operation! Pair of high-end ribbon tweeters, matched, 25 WMAX, 12 WRMS, 7 Ω Real ribbon tweeter with neodymium magnet system and transformer Due to horn front attachment, a very high sound pressure and even beaming Fine and brilliant reproduction of the high frequency range Smooth, unembossed aluminium sandwich cone: 9x60x0.015 mm For use from 2,500 Hz on via 18 dB filter Horn with mounting flange and protective grille | Impedance (Z) 7 Ω Resonant frequency (fs) - Max. frequency range 1,100-30,000 Hz Rec. crossov. frequ. (fmax.) (12 dB/oct.) > 3,000 Hz Music power 25 WMAX Power rating (P) 12 WRMS SPL (1 W/1 m) 96 dB Radiation angle (vert./hor.) - Voice coil diameter - Magnet diameter neodymium rods Mounting cutout 70x90 mm Mounting depth 101 mm Dimensions 98x110x101 mm Weight 520 g
2.599,00 kr
-
Monacor SP-10/250PRO 10" Bas PA Højttaler - 250W 8 Ohm med god Bas"
SP-8/150PRO and SP-10/250PROare PA speakers of long excursion and high power capability, with diecast aluminium basket, rear-ventilated centering spider and ventilated drive system for a high thermal stability. They feature ideal parameters for a very good bass reproduction in compact bass-reflex cabinets. PA bass speaker, subwoofer, 500 WMAX, 250 WRMS, 8 Ω 25 cm (10") bass speaker and subwoofer of high power capability Heat-resistant voice coil and ventilated drive system Drive configuration of very long excursion for a deep bass reproduction of high volumes Progressive cone suspension for a high operating reliability Robust diecast aluminium basket Ideally suited for compact subwoofers and 2-way systems with a crossover frequency of approx. 1,500 Hz to the tweeter HOBBY HiFi 03/2014"A bass driver of particularly long excursion and high level stability for compact cabinets of about 35 litres (e.g. in the speaker building concept HiFi-PA 10/2). The HiFi-PA 10/2 impressed with a breathtaking power in the audio room. ... tremendous level reserves ... incredibly filigree."HOBBY HiFi 02/2014"A bass driver of particularly long excursion and high level stability for more compact reflex cabinets of about 35 to 40 litres." Klang + Ton 03/2013"Universal bass speaker for powerful applications. Skilfully selected TSP ensure high subwoofer levels from compact cabinets." | Impedance (Z) 8 Ω Resonant frequency (fs) 47 Hz Max. frequency range f3-2,000 Hz Music power 500 WMAX Power rating (P) 250 WRMS SPL (1 W/m) 94 dB Suspension compl. (Cms) 0.20 mm/N Moving mass (Mms) 51 g Mech. Q factor (Qms) 6.16 Electr. Q factor (Qes) 0.35 Total Q factor (Qts) 0.33 Equivalent volume (Vas) 40.7 l DC resistance (Re) 7.1 Ω Force factor (BxL) 18.3 Voice coil induct. (Le) 0.83 mH Voice coil diameter Ø 75 mm Voice coil former Kapton Linear excursion (XMAX) ±7 mm Eff. cone area (Sd) 380 cm2 Magnet weight 2 kg Weight 5.2 kg
1.149,00 kr
-
Monacor 15" Basenhed SP-15A/402PA | Hi-Fi & PA 800W - Høj Følsomhed"
SP-15A/402PA er en 15” basenhed der egner sig en flot Hi-fi oplevelse og med sin høje følsomhed på 100dB og max belastning på 800W er et PA job naturligvis også en mulighed. Med sin lave Qts på 0,31 og resonans frekvens på 36Hz, kan en voldsom dybbas opnåes på blot 200 liter og 4x MBR-100 basrefleks rør (F3 43Hz). Det kan måske lyde meget almindeligt i første omgang, men i dette tilfælde er den F3 frekvens spillet med helt op til 126 decibel, som gør at denne bas er meget magtfuld og dynamisk. Den høje følsomhed gør denne enhed også til et godt match til en rørforstærker og dens typisk begrændset udgangs effekt. Dermed også et godt match til horn drivere, til at lave en hi-fi højttaler med lav drifteffekt. Selve enheden er udført pænt og seriøst med støbt chassis og coated pap-membran. Professional Speakers from IMG Stage LineOf very high power capability, high efficiency and with drive parameters which allow a reproduction of the complete bass range. These speakers guarantee excellent results as bass-midrange speakers in 2-way or multiway systems as well as subwoofers with the two larger models. Professional PA bass speaker, 800 WMAX, 400 WRMS, 8 Ω Of very high power capability 38 cm (15") professional bass speaker of long excursion Diecast basket Cone with water-repellent coating Very neat workmanship with a facing basket front Wide frequency response High efficiency Excellent deep bass reproduction Drive system with drilled pole core and additional magnet for optimising the magnetic field and impedance linearisation For bass-reflex cabinets of medium size from 80 litres on For all kinds of professional and semiprofessional PA applications | Impedance (Z) 8 Ω Resonant frequency (fs) 36 Hz Max. frequency range f3-3,000 Hz Music power 800 WMAX Power rating (P) 400 WRMS SPL (1 W/m) 100 dB Suspension compl. (Cms) 0.22 mm/N Moving mass (Mms) 87 g Mech. Q factor (Qms) 7.45 Electr. Q factor (Qes) 0.33 Total Q factor (Qts) 0.31 Equivalent volume (Vas) 235 l DC resistance (Re) 6.5 Ω Force factor (BxL) 19.9 Tm Voice coil induct. (Le) 0.9 mH Voice coil diameter 100 mm Voice coil former Kapton Linear excursion (XMAX) ±5 mm Eff. cone area (Sd) 881 cm2 Magnet weight 2.3 kg Weight 8 kg
1.995,00 kr
-
Monacor SP-12A/302PA 12" Basenhed - Perfekt til Hi-Fi og PA
SP-12A/302PA er en 12” basenhed der virkelig producere et flot stramt lydbilled med masser af magt, der er oplagt til musik med høj dynamik, såsom klassisk. Derfor finder du denne basenhed i vores byggesæt Menhir, som virkelig kan tage noget seriøs crescendo. Den har gengivelse helt op til 4000Hz men til high-end hi-fi bør delefrekvensen holdes under 1600Hz. Flot udført enhed med støbt chassis, coated pap-membran og forgyldte klemme terminaler. Professional Speakers from IMG Stage LineOf very high power capability, high efficiency and with drive parameters which allow a reproduction of the complete bass range. These speakers guarantee excellent results as bass-midrange speakers in 2-way or multiway systems as well as subwoofers with the two larger models. Professional PA bass-midrange speaker, 600 WMAX, 300 WRMS, 8 Ω Of very high power capability 30 cm (12") professional speaker of long excursion Diecast basket Cone with water-repellent coating Very neat workmanship with facing basket front Wide frequency response of low distortion High efficiency Excellent bass reproduction Drive system with drilled pole core and additional magnet for optimising the magnetic field and impedance linearisation For bass-reflex cabinets from 30 litres on already For all kinds of professinal and semiprofessional PA applications HOBBY HiFi 05/2013"With the SP-12A/302PA, IMG Stage Line offers a bass speaker of high power capability for 3-way systems which features an impressively deep bass, a superior level stability and an excellent sound quality." | Impedance (Z) 8 Ω Resonant frequency (fs) 50 Hz Max. frequency range f3-4,000 Hz Music power 600 WMAX Power rating (P) 300 WRMS SPL (1 W/m) 99 dB Suspension compl. (Cms) 0.19 mm/N Moving mass (Mms) 50 g Mech. Q factor (Qms) 7.87 Electr. Q factor (Qes) 0.35 Total Q factor (Qts) 0.34 Equivalent volume (Vas) 77 l DC resistance (Re) 6.4 Ω Force factor (BxL) 16.98 Tm Voice coil induct. (Le) 0.8 mH Voice coil diameter 66 mm Voice coil former Kapton Linear excursion (XMAX) ±5 mm Eff. cone area (Sd) 530 cm2 Magnet weight 2 kg Weight 5.2 kg
1.299,00 kr
-
Monacor IMG Stage Line SP-10A/302PA 10" Bas-Højttaler - 300W RMS, Vandafvisende"
Professional Speakers from IMG Stage LineOf very high power capability, high efficiency and with drive parameters which allow a reproduction of the complete bass range. These speakers guarantee excellent results as bass-midrange speakers in 2-way or multiway systems as well as subwoofers with the two larger models. Professional PA bass-midrange speaker, 600 WMAX, 300 WRMS, 8 Ω Of very high power capability 25 cm (10") professional speaker of long excursion Diecast basket Cone with water-repellent coating Very neat workmanship with a facing basket front Wide frequency response of low distortion High efficiency Drive system with drilled pole core and additional magnet for optimising the magnetic field and impedance linearisation For compact bass-reflex cabinets from 20 litres on already For all kinds of professional and semiprofessional PA applications | Impedance (Z) 8 Ω Resonant frequency (fs) 55 Hz Max. frequency range f3-3,500 Hz Music power 600 WMAX Power rating (P) 300 WRMS SPL (1 W/m) 98 dB Suspension compl. (Cms) 0.24 mm/N Moving mass (Mms) 35 g Mech. Q factor (Qms) 7.44 Electr. Q factor (Qes) 0.31 Total Q factor (Qts) 0.30 Equivalent volume (Vas) 40 l DC resistance (Re) 6.4 Ω Force factor (BxL) 15.82 Tm Voice coil induct. (Le) 0.65 mH Voice coil diameter 66 mm Voice coil former Kapton Linear excursion (XMAX) ±4 mm Eff. cone area (Sd) 346 cm2 Magnet weight 2 kg Weight 5 kg
1.399,00 kr
-
Monacor SP-100/8 HiFi Bas/Mellemtonehøjttaler 4" 60W - Robust & Klar Lyd
Hi-fi bass-midrange speaker, 60 WMAX, 30 WRMS, 8 Ω Robust paper cone High-quality aluminium coil Drilled pole core Rubber surround Excellent radiation and transient response | Impedance (Z) 8 Ω Resonant frequency (fs) 61 Hz Max. frequency range f3-7,000 Hz Music power 60 WMAX Power rating (P) 30 WRMS SPL (1 W/m) 88 dB Suspension compl. (Cms) 1.23 mm/N Moving mass (Mms) 5.5 g Mech. Q factor (Qms) 2.28 Electr. Q factor (Qes) 0.44 Total Q factor (Qts) 0.37 Equivalent volume (Vas) 4.7 l DC resistance (Re) 6.5 Ω Force factor (BxL) 5.55 Tm Voice coil induct. (Le) 0.4 mH Voice coil diameter 25 mm Voice coil former aluminium Linear excursion (XMAX) ±2.5 mm Eff. cone area (Sd) 52 cm2 Magnet weight 280 g Weight 0.8 kg
269,00 kr
-
Monacor SP-12/200PA 12" DJ/Scene PA Højttaler - 400W, 200W RMS, 8Ω Bas-Mellemtone"
High-Quality PA SpeakersFor general stage and professional DJ applications. Excellent workmanship and perfect specifications for bass-reflex speaker systems of high power capability. PA bass-midrange speaker, 400 WMAX, 200 WRMS, 8 Ω Very high efficiency and perfect specifications for the use in compact full range speaker systems Can ideally be combined with mid-high range horns | Impedance (Z) 8 Ω Resonant frequency (fs) 45 Hz Max. frequency range f3-5,000 Hz Music power 400 WMAX Power rating (P) 200 WRMS SPL (1 W/m) 100 dB Suspension compl. (Cms) 0.29 mm/N Moving mass (Mms) 43 g Mech. Q factor (Qms) 5.20 Electr. Q factor (Qes) 0.35 Total Q factor (Qts) 0.33 Equivalent volume (Vas) 114 l DC resistance (Re) 6.8 Ω Force factor (BxL) 15.4 Tm Voice coil induct. (Le) 1.2 mH Voice coil diameter 78 mm Voice coil former Kapton Linear excursion (XMAX) ±4 mm Eff. cone area (Sd) 531 cm2 Magnet weight 1.8 kg Weight 6 kg
1.149,00 kr
-
Monacor SP-8/150PA 8" Bas-Mellemtone Højttaler 150W RMS - Effektiv & punchy"
PA bass-midrange speaker, 300 WMAX, 150 WRMS, 8 Ω Good medium efficiency Wide bandwidth radiation for midrange applications | Impedance (Z) 8 Ω Resonant frequency (fs) 88 Hz Max. frequency range f3-8,000 Hz Music power 300 WMAX Power rating (P) 150 WRMS SPL (1 W/m) 96 dB Suspension compl. (Cms) 0.16 mm/N Moving mass (Mms) 20 g Mech. Q factor (Qms) 4.12 Electr. Q factor (Qes) 0.48 Total Q factor (Qts) 0.43 Equivalent volume (Vas) 12 l DC resistance (Re) 6.9 Ω Force factor (BxL) 12.6 Tm Voice coil induct. (Le) 0.6 mH Voice coil diameter 50 mm Voice coil former Kapton Linear excursion (XMAX) ±1.25 mm Eff. cone area (Sd) 219 cm2 Magnet weight 1.1 kg Weight 3 kg
599,00 kr
